Reply to thread

Message

<blockquote data-quote="Astromath" data-source="post: 6767954" data-attributes="member: 78315">A couple of possible improvements:1)&nbsp; On page 1 you have the Ability Save DC.&nbsp; Since the dragonborn's breath weapon is based on a CON save DC, I think it would be proper to put that there and use the 2nd Ability Save DC for the spellcasters.2)&nbsp; Speaking of Ability Save DCs, how about putting that circle to the right of each ability.&nbsp; I know it might be a little difficult to rearrange the sheet to allow that.&nbsp; You could then replace the Ability Save DC area with the Inspiration area.&nbsp; The Senses would be pushed right and lengthened.&nbsp; The Limited Features would need to be shortened, but the Saving Throw area could be lengthened.&nbsp; I'm including an attachment to show how I envision it to be.&nbsp; The ASDCs would only be filled in only if a class or a race needed them.&nbsp; So, a human barbarian would have none of the ASDCs filled in.&nbsp; A dragonborn fighter would only have the CON ASDC filled in.&nbsp; A dragonborn wizard would have CON &amp; INT ASDCs filled in.&nbsp; If you want, you could add a toggle or a checkbox to force the others to show or not.3)&nbsp; When choosing the Barbarian with the dragonborn, there's a slight problem when reaching level 3 and choosing the Bear Totem.&nbsp; When choosing Barbarian, you get the resistances to bludgeoning, slashing, and piercing resistances using three lines of the Resistance area of the Defense block.&nbsp; If you choose dragonborn after choosing barbarian, the dragon type resistance is listed on the 4th line of the resistance area.&nbsp; Here comes the problem:&nbsp; when choosing the bear totem, the three lines of resistances shrink down to 1 line leaving the dragon type resistance on the 4th line.&nbsp; This leaves 2 blank lines between the 2 different resistances.&nbsp; I know the workaround would be to either manually change the resistance listed on the 4th line to the 2nd, or choose dragonborn first and then the barbarian class.</blockquote>

[QUOTE="Astromath, post: 6767954, member: 78315"] A couple of possible improvements: 1) On page 1 you have the Ability Save DC. Since the dragonborn's breath weapon is based on a CON save DC, I think it would be proper to put that there and use the 2nd Ability Save DC for the spellcasters. 2) Speaking of Ability Save DCs, how about putting that circle to the right of each ability. I know it might be a little difficult to rearrange the sheet to allow that. You could then replace the Ability Save DC area with the Inspiration area. The Senses would be pushed right and lengthened. The Limited Features would need to be shortened, but the Saving Throw area could be lengthened. I'm including an attachment to show how I envision it to be. The ASDCs would only be filled in only if a class or a race needed them. So, a human barbarian would have none of the ASDCs filled in. A dragonborn fighter would only have the CON ASDC filled in. A dragonborn wizard would have CON & INT ASDCs filled in. If you want, you could add a toggle or a checkbox to force the others to show or not. 3) When choosing the Barbarian with the dragonborn, there's a slight problem when reaching level 3 and choosing the Bear Totem. When choosing Barbarian, you get the resistances to bludgeoning, slashing, and piercing resistances using three lines of the Resistance area of the Defense block. If you choose dragonborn after choosing barbarian, the dragon type resistance is listed on the 4th line of the resistance area. Here comes the problem: when choosing the bear totem, the three lines of resistances shrink down to 1 line leaving the dragon type resistance on the 4th line. This leaves 2 blank lines between the 2 different resistances. I know the workaround would be to either manually change the resistance listed on the 4th line to the 2nd, or choose dragonborn first and then the barbarian class. [/QUOTE]

Verification